SPL Phonitor 3 DAC | 120V headphone amplifier
2.499€
- Headphone amplifier with DAC and 120v technology
- with Phonitor Matrix
- VU-Meter
- Burr-Brown OPA 2134 SoundPlus™ Operational Amplifier
Available in our demo studio Dresden. Arrange appointment
The Phonitor 3 DAC is not only the ultimate headphone amplifier and monitor controller with 120V technology – the integrated DAC makes it the perfect monitoring center for demanding producers as well as sound and mastering engineers working with digital feeds or directly in the DAW.
Whether USB, AES/EBU or S/PDIF – the integrated DAC with analogue SLP120 converts digital PCM audio signals with a resolution of 32 bits and a sampling rate of up to 768 kHz. It converts DSD signals with a resolution of up to DSD256.
On the analog side, the Phonitor 3 DAC, based on SPL 120V technology, offers the same monitoring quality over speakers and headphones as the big SPL mastering consoles. The analog phonitor matrix makes it possible to mix and master in the highest quality over headphones – with the same spatial perception of the stereo stage as over loudspeakers.
There is a dip switch on the bottom of the device. Here, for the RCA jacks, the consumer level can be raised from -10 dBV to 0 dBu for CD players and other HiFi equipment.
In addition, the volume control can be remotely controlled via infrared operation. To do this, press the Learn button on the back of the headphone amplifier and teach the corresponding louder and quieter buttons.
- Maximum input level: 32.5dBu
- Input impedance (RCA): 10kΩ
- Input impedance (XLR): 20kΩ
- Output impedance (XLR): 75Ω
- Common mode rejection: -82dB
- Frequency response (-3dB): 10Hz – 100kHz
- THD +N (10Hz – 22kHz, 0dBu): 0.0009%.
- Noise (A-weighted): -102dBu
- Crosstalk (1 kHz): -95dB
- Dynamic range: 134.5dB
- AES/EBU (XLR), PCM sampling rates: 44.1/48/88.2/96/176.4/192 kHz
- Coaxial SPDIF (Cinch), PCM sampling rates: 44.1/48/88.2/96/176.4/192 kHz
- Optical SPDIF (Toslink F06), PCM sampling rates: 44.1/48/88.2/96/with fiber < 1m: 176.4/192 kHz
- USB (B), PCM sampling rates: 44.1/48/88.2/96/176.4/192/352.8/384/705.6/768 kHz
- USB (B), DSD over PCM (DoP), sampling rates: 2.8 (DSD64), 5.6 (DSD128), 11.2 (DSD256) MHz
- 0 dBfs calibrated to: 15 dBu
- Swelling resistance: 0.18Ω
- Attenuation factor (40Ω): 180
- Frequency response (-3dB): 10Hz – 100kHz
- Crosstalk (1kHz): -91dB
- THD + N (0dBu, 10Hz – 22kHz): 0.00091%
- Noise (A-weighted): -102dBu
- Output power (1kHz, 1% THD, 600Ω): 2x 2.7W
- Output power (1kHz, 1% THD, 250Ω): 2x 5V
- Output power (1kHz, 1% THD, 32Ω): 2x 1W
- Dynamic range: 134.5dB
DAC 120 Volt
The converter chip in the Phonitor 3 DAC’s digital-to-analog converter is the highly acclaimed AKM AK4490 Velvet Sound™ premium DAC chip, whose architecture reproduces the finest sonic details. It converts PCM audio with a resolution of 32 bits and a sampling rate of up to 768 kHz, which is 16 times the CD resolution. Direct Stream Digital is supported up to a resolution of DSD4 or DSD256.
Every signal that is passed from a DAC chip into the analog world must be filtered through a low-pass filter. Unlike any other DAC in the world, our analog low-pass filters use SPL 120V technology, which adds dynamic range, headroom and sound. The DAC in the Phonitor 3 DAC is equipped with the SLP120 – an analog “single low pass” filter with 120V technology.
Conventional
Phonitor Matrix
Channel crosstalk
Optional extensions for the Phonitor 3
Expansion Rack
The Phonitor 3 can be expanded into a full-featured monitor controller by adding an Expansion Rack.
In the expansion rack, the phonitor is installed in a 19″ housing. This allows the headphone amplifier to be installed in a studio desk or rack.
There is a module that is connected to the main out of the Phonitor 3. The add-on module provides four outputs for speaker pairs and a controller knob to select the desired speaker. This turns the Phonitor 3 into a full-featured monitor controller.
Weight | 6,5 kg |
---|---|
Dimensions | 54 × 38 × 18 cm |
Color | Black |
Headphone Jack | Yes |
Channels | Stereo |
Port | AES/EBU, Cinch, S/PDIF, Toslink, USB, XLR |
Only logged in customers who have purchased this product may leave a review.
Q & A
Ask a question
Your question will be answered by a store representative or other customers.
Thank you for the question!
Your question has been received and will be answered soon. Please do not submit the same question again.
Error
An error occurred when saving your question. Please report it to the website administrator. Additional information:
Add an answer
Thank you for the answer!
Your answer has been received and will be published soon. Please do not submit the same answer again.
Error
An error occurred when saving your answer. Please report it to the website administrator. Additional information:
You may also like…
- Monitor Controller
- Speaker + Subwoofer Outputs
- Headphone jack with phonitor matrix
- Headphone amplifier with 32 Bit DAC
- with Phonitor Matrix
- 2 analog inputs + USB port
- Burr-Brown OPA 2134 SoundPlus™ operational amplifier
- Headphone amplifier with DAC and 120v technology
- with Phonitor Matrix and Monitor Controller
- VU-Meter
- Burr-Brown OPA 2134 SoundPlus™ Operational Amplifier
Available in our demo studio Dresden. Arrange appointment
- Extension for Phonitor 2 + SMC 7.1
- 1 XLR stereo input
- 4 XLR stereo outputs
Related Products
- active 2-way monitor
- 18cm woofer + 3,5cm tweeter
- XLR and RCA connection
- active 1-way mini monitor
- 5,25″ woofer
- XLR and jack connection
- passive 1-way mini monitor
- 5,25″ woofer
- Connection for speaker wire, cable lugs and double banana plugs
- active 1-way mini monitor
- 5,25″ woofer
- XLR and jack connection
- Monitor Controller
- High-end preamplifier
- 8 inputs and outputs
- Poti and switches from ALPS
Reviews
There are no reviews yet