SPL Audio Control One
559€
- Monitor Controller
- Speaker + Subwoofer Outputs
- Headphone jack with phonitor matrix
Analog inputs & outputs; 6.35mm stereo jacks:
- max. input level: +22.5dBu
- Line Input 1 (balanced)
- input impedance: 20kΩ
- common mode rejection: < 60dB
- Line Input 2 (unbalanced) Input impedance: 10kΩ
- Output level (max.) Speaker Outputs (600Ω): +22dBu
- Line Output (unbalanced) Output impedance: 75Ω
- Speaker Output 1 (balanced) Output impedance: 150Ω
- Sub Output Low Filter: none (Full Range)
- Sub Output (balanced) Output impedance: 150Ω
- Speaker Output 2 (unbalanced) Output impedance: 75Ω
- Frequency response (-3dB): 10Hz – 200kHz
- Dynamic range: 121dB
- Noise (A-weighted, 600Ω load): -99dBu
- THD + N (0dBu, 10Hz – 22kHz): 0.002%.
- Crosstalk (1kHz): < 75dB
- Fade-out attenuation: -93dB
Monitor Controller
The Control One offers three different monitoring modes. These are adjustable via a switch on the front. In the center position, the signal is played back as a completely normal stereo signal. To check the mono compatibility, the switch is set to “Mono”. The third switch position is a special function. Here the left and right sides of the signal are swapped. This is especially useful for video dubbing. If you are looking for samples in the library that should match the direction of movement, you can quickly swap the channels if they do not match the picture. With the L/R > R/L function it is possible to swap the direction of movement already during pre-listening.
Furthermore, the controller has two stereo inputs for players such as a DA converter, CD player or mixer. Just like the speaker outputs, the corresponding input can be controlled via a switch on the front panel. In the center position, Input 1 + 2 are mixed together.
The output stage of the headphone amplifier is designed as a push-pull amplifier in Class AB operation. Thanks to the bipolar transistors, a higher gain and a larger output voltage is thus possible. They are thermally coupled, which contributes to a consistent and stable sound image.
Built into the headphone amplifier is the revolutionary Phonitor Matrix, which allows you to create mixes through headphones that sound just like they do through speakers. The Phonitor Matrix includes three parameters: Crossfeed, Speaker Angle and Center Level. In Control One the most used values of Center Level and Speaker Angle are set. The center level is -1dB and the speaker angle is 30°. Crossfeed determines the crosstalk of the two channels and is continuously adjustable in this device. This function is only in the audio path as soon as it is added by relay control.
Headphone output
- 6.35mm stereo phone jack: tip = left, ring = right, shank = GND
- source resistance: 20Ω
- Frequency response (-3dB): 10Hz – 200kHz
- Noise (A-weighted, 600Ω): -97dBu
- THD + N (0dBu, 10Hz – 22kHz, 600Ω): 0.002%.
- THD + N (0dBu, 10Hz – 22kHz, 32Ω): 0.013%.
- Max. Output power (1kHz, 600Ω): 2 x 190mW
- Max. Output power (1kHz, 250Ω): 2 x 330mW
- Max. Output power (1kHz, 47Ω): 2 x 400mW
- Crosstalk attenuation (600Ω): -99dB
- Crosstalk (1kHz, 600Ω): -75dB
- Dynamic range (600Ω): 117dB
PHONITOR MATRIX
Conventional
Phonitor Matrix
Channel crosstalk
Weight | 2 kg |
---|---|
Dimensions | 38 × 27 × 7,5 cm |
Channels | Stereo |
Port | sym. Jack, unsym. Jack |
Only logged in customers who have purchased this product may leave a review.
Q & A
Ask a question
Your question will be answered by a store representative or other customers.
Thank you for the question!
Your question has been received and will be answered soon. Please do not submit the same question again.
Error
An error occurred when saving your question. Please report it to the website administrator. Additional information:
Add an answer
Thank you for the answer!
Your answer has been received and will be published soon. Please do not submit the same answer again.
Error
An error occurred when saving your answer. Please report it to the website administrator. Additional information:
Related Products
- Monitor Controller
- with headphone jack
- Phonitor Matrix
- 32-bit AD/DA converter
Stereo amplifier
analog stereo input and output
Status LED with clipping indicator
- active 2-way monitor
- 18cm woofer + 3,5cm tweeter
- XLR and RCA connection
- active 3-way studio speaker
- 6,8″ woofer + 2,2″ midrange + 1″ tweeter
- active phase correction (CPR system)
- Monitor Controller
- High-end preamplifier
- 8 inputs and outputs
- Poti and switches from ALPS
Reviews
There are no reviews yet