Sonarworks SoundID Reference for Speakers & Headphones + Measurement Microphone
269€
- Speaker calibration
- Headphone calibration profiles for more than 480 supported models
- Translation Check: Simulation of over 20 different devices and device types
Sonarworks SoundID Reference is speaker and headphone calibration software that delivers consistently accurate studio reference sound.
In less than 20 minutes, studio speakers can be calibrated with a SoundID Reference measurement microphone. Headphones can be calibrated with more than 480 supplied headphone profiles.
With the appropriate calibration profile, the software adjusts the frequency response to be completely flat across all audible frequencies. In addition, user-defined target curves can be created and custom adjustments can be made for the target curve in real time.
The precise studio reference sound can be seamlessly switched between different speakers, headphones and rooms.
- Speaker calibration
- Headphone calibration profiles for more than 480 supported models
- User-defined target: adjust the target curve in real time
- Translation Check: Simulation of over 20 different devices and device types
- 3 filter modes: Zero Latency, Mixed and Linear Phase
- Additional DSP processing controls: Mono, Dry/Wet and Safe Headroom
- MIDI assignment in the SoundID Reference App for various controls
- User presets in the SoundID Reference App for quick switching between
predefined output device/channel pair combinations
Scope of delivery
- SoundID Reference stand-alone + DAW plug-in (AU, VST, AAX)
- SoundID Reference measurement microphone (XLR connector) + individual calibration
profile - Activation of the licence possible on up to 3 devices simultaneously
Microphone specifications
- Capsule: pre-polarised electret condenser capsule
- Polar pattern: omnidirectional
- Frequency response: 20 Hz – 20 kHz with a supplied calibration profile
- Sensitivity: -37 dB/Pa (14 mV)
- Inherent noise: 24 dB
- Signal-to-noise ratio: 70 dB
- Dynamic range: 106 dB
- Maximum sound pressure level: 132 dB
Requirements
- Mac: macOS 10.12 or higher
- PC: Windows 8 (64-bit) or higher
- 2.0 or 2.1 stereo speaker system or
- Supported headphones or headphones individually calibrated by Sonarworks
- Audio interface with +48 V phantom power and 44.1 kHz sampling rate
- XLR audio cable
| Version | Speaker & Headphones + Mic |
|---|
Only logged in customers who have purchased this product may leave a review.
Q & A
Ask a question
Your question will be answered by a store representative or other customers.
Thank you for the question!
Your question has been received and will be answered soon. Please do not submit the same question again.
Error
An error occurred when saving your question. Please report it to the website administrator. Additional information:
Add an answer
Thank you for the answer!
Your answer has been received and will be published soon. Please do not submit the same answer again.
Error
An error occurred when saving your answer. Please report it to the website administrator. Additional information:
Related Products
- Drum Microphone Set
- Condenser & Dynamic Microphones
- Polar pattern: cardioid, hypercardioid
- 20Hz – 16kHz
- Kick Drum Microphone Set (KICK + MONDO)
- Dynamic voice coil + dynamic microphone
- Polar pattern: Eight + Cardioid
- 50Hz – 2kHz + 20Hz -15kHz
- FET condenser microphone, large diaphragm
- Polar pattern: cardioid
- 35Hz – 20kHz (+/-3.5dB)
- -10dB pad switch, 80Hz low cut switch
- FET condenser microphone
- Polar pattern: omnidirectional, cardioid, hypercardioid
- 25Hz – 20kHz (+/-3dB)
- -10dB pad switch, 80Hz low cut switch
- Small diaphragm condenser microphone
- Cardioid
- -10dB pad
- for tom drums
Reviews
There are no reviews yet